Products

Used at higher frequencies than traditional shielding and can also be used with other EMI/RFI shields to extend frequency range.

Electrically Conductive rubber products for grounding, contact point, water tight rings or flexible springs.

Double layer rubber table mat with excellent grounding properties, available in different colours and in complete rolls or pre-cut

Anti static tubes with an electrically conductive wall to shield your electrical and chemical or liquid materials

Silicone shielding elastomers are a 30-durometer, electrically conductive, silver-aluminium silicone shielding elastomer, softer than many other EMI materials

Wrapshield is a knitted wire mesh for EMI/RFI cable shielding

Ready-made sleeves can be supplied in Amucor or in conductive fabric. The material provides high shielding performance.

Flexible cable shield for EMI shielding of flexible cables. Branches are easy to realize.

Ready-made round sleeve (EMI-screening sleeve) easy cable routing with high shielding performance

Mu-copper cable shielding, flexible shielding tube for high shielding performance. A wide range of cable diameters can be shielded with a single tube.

Flat cable connector shields used to shield flat cable connectors and get a high shielding performance

EMI flange seals for electrical connectors, provided with self-adhesive

EMI / RFI Shielded cable entry system to mount, ground and shield several cables or bundles of cables simultaneously.

Easy to be stuck to any HDMI connector to create a high shielding performance HDMI cable

Easy connector shielding without replacing the whole connector.

Tin plated braided copper wire EMI cable shielding in a wide range of diameters for high shielding performance.

Mu-ferro foil and tape has been developed for low-frequency (LF) magnetic field shielding.

HF-Closed (EMC) Cable Entry Gland with metric and PG- line - nickel-plated with IRIS-suspension. Excellent EMI/RFI shielding for screened cables.

High performance cable gland to seal your shielded cable at the end both waterproof and EMI.

Cable grounding clamps for EMI/RFI shielding and ESD suppression. Clamps can be used as an end piece for cable shields or can be used with the Wrapshield 4730-4760-series or the Full metal flexible cable shielding 4800-series.

Cable grounding straps for EMI/RFI shielding and ESD suppression.

Convenient tie-wrap for cable shielding, EMI cable-shielding tie-wrap is used for fast, reliable, and cost-effective RFI/EMI/EMP shield terminations.

Used for cables and connectors & easy to use.

For a tight seal with high shielding performance for cables and connectors

For a tight seal with high shielding performance for cables and connectors

Flexible EMI shield for bundles of cables or for cables with big connectors.

The zippershield is made to shield bundles of cables or for cables with big connectors through a sleeve to create excellent EMI shielding.

A braided tinned steel that wraps by itself around your cable

Protect and shield your cables with easy velcro or zipper closure

Easy and protective sleeve for your shielded cables

Shielded clamps to weaken the unwantede interference current

Shielding, grounding and attaching of cables to and from the equipment in your shielded enclosure

Shielded connector hoods are ideal for indoor signal or power applications requiring robustness and/or high EMI/RFI performance in the industrial and telecommunications business.

Anti static tubes with an electrically conductive wall to shield your electrical and chemical or liquid materials

Shielding hoses with aluminium layer for EMI/RFI shielding of cables.

Polyester braided sleeving is suitable for the mechanical protection of harnesses

Stainless steel spiral hose used as steel carrier is a general purpose high quality connecting hose

Stainless steel spiral hose used as steel carrier is a general purpose high quality connecting hose

Flexible braids absorb elongation and shortening due to heat.

Used at higher frequencies than traditional shielding and can also be used with other EMI/RFI shields to extend frequency range.

Ferrite absorber tile is the industry standard solution and exhibits excellent overall performance versus cost

Ferrite absorber tile is the industry standard solution and exhibits excellent overall performance versus cost

Special design for small EMC anechoic chamber to get excellent electromagnetic absorption performance in 30 MHz to 2 GHz.

For the construction of a small anechoic chamber to get a larger space than one could build with pyramid-shaped absorbers. Performs very well in wide band (30 MHz to 18 GHz)

PU foam based pyramid absorbers are the most popular solution for 3, 5 and 10 m EMC chambers in the market.

Absorbers in the floor improve the "quite zone" and with these a normal person can walk on them or add equipment.

These absorbers can be used at higher frequencies than traditional shielding and can also be used with other EMI/RFI shields to extend frequency range.

EPP outdoor absorber for various EMC, microwave chambers and outdoor usage

Almost has the same performance in low frequency as the pyramid absorbers (with tips); but its performance in high frequency might be slightly declined

The main advantage is to reduce the back scattering of pyramid absorbers get an even more quiet quiet zone.

Nonflammable high power handling EM absorbers for anechoic chambers.

Microporous pyramid absorbers can support inside and outside ventilation circulation.

High-power silicon carbide pyramid absorbing material. Low power esistance, easy to install

Rubber flat narrow band absorber is a thin flexible narrow band resonating radar absorbent.

Absober optimalized for in EMC chambers

Antenna measurement in anechoic rooms on high frequency range

The flexible EMI absorber sheets, developed for electromagnetic-wave absorption and noise suppression, can eliminate noise effectively.

Works as a high frequency absorber & thermal conduction composite

EMC/EMI problems can be solved by simply attaching EM absorber and noise suppression sheets on (part of) the noise sources.

Our prefabricated self-standing modular Faraday cages offer superior screening of RF/LF/HF signals, e.g. for R&D, TEMPEST, Sensitive Compartmented Information Facility (SCIF) and Testing purposes.

EMI shielding metal racks and enclosures, standard size or fully customized

Safes to store RFID in a secure way

Shielded TFT screen and touchscreen computers for applications where no attenuation is allowed from the screen.

Life cycle of screen is short, so shielded housing is more economic in time.

EMI/EMC shielded bellows for a easy connection for cable shielding

Conductive mesh is coated Nickel and Copper over Polyester Fabrics. It offers excellent surface conductivity, shielding effectiveness, and corrosion resistance for a variety of application.

A shielded transparent film in order to apply on standard displays, glass, acrylic, polycarbonate etc.

PET film deposited with copper grid and protected with a nickel layer for EMI shielded windows & displays. High light transmission, excellent EMI shielding.

Float glass with a conductive coating layer on one side for EMI/RFI shielding

EMI/RFI shielded mesh foil windows and electrically conductive windows with high EMI/RFI shielding performance. Windows for Electromagnetic Compatibility.

Transparent static dissipative, self-adhesive Polyester film. It includes a special coating on one side and a release film on the other side.

A polyester film with a layer of transparent conductive coating. This offers excellent electrical and electromagnetic shielding.

Ready-made transparent EMI-shielding foil windows for moderate EMI shielding, with good light transmittance and transparency.

Ready to install Faraday cage windows. These windows guarantee very high EMI / RFI / EMC shielding performance

Ideal EMI/RFI shield for electronic displays requiring moderate shielding effectiveness and high-quality optical properties.

Light weight material conductive mesh offers excellent surface conductivity.

Shielded window designed for the high EMI/RFI and low frequency shielding

Used as a bezel for windows or other contacts.

developed for different EMI/EMC applications and a effective EMI shielding materials

We can print/coat ITO on any (transparent) surface

A signaljammer car must be shielded to protect the people who drive the car against the massive electromagnetic fields and radio frequencies that are spread and sent by the jammers on top of the car.

Cost effective instant Faraday tent for EMC experiments, RF measurements, mobile military / forensic activities and personal protection.

Amucor foil has high attenuation properties in the electrical field (up to 100 dB) as well as in the magnetic field. It is easy to apply, like wallpaper, thanks to its special adhesive for walls, ceilings and floors. The interior finish can be plaster board, foam tiles or plywood.

Safe data transport with the shielded briefcase

A signaljammer car must be shielded to protect the people who drive the car against the massive electromagnetic fields and radio frequencies that are spread and sent by the jammers on top of the car.

The briefcase blocks wireless communication and sound recording

Lightweight, flexible and high performing RF / EMI Shielding Pouches

A shielded box for smartphones, so that there is no connection with the phone.

Anti microbial copper textile to kill bacteria, viruses and fungi.

Energy saving strip to place around windows and doors against draft

Mu-copper housings and enclosures for EMI shielding of PCB’s

Life cycle of screen is short, so shielded housing is more economic in time.

High performance double-layer shielded enclosures, produced in any shape or size

We provide customized solutions for EMI shields, grounding contacts, flexible antenna paths, electrically conductive connections, current flows, ESD/EMC stickers to shield plastic housings and more - for a wide variety of applications.

High performance shielded housing for PCB. Big range of size available. Good shielding properties, optionally in addition with PCB- shields for shielding near to the source.

Suited for safe use in gas /vapor zone 1 hazardous locations

EMI shielded ventilation panels for ventilation and heating in screened rooms, EMI shielding rooms & Faraday cages

EMI shielded ventilation panels for ventilation and heating without frame. Possible with compressed flange.

Honeycomb ventilation shields are designed to provide EMI shielding and maximum air flow without degrading the fan output. For fans in e.g. computer cases

Honeycomb fan shield ventilation panel with threaded holes for easy installation in e.g. computer cases to provide EMI shielding and maximum airflow without degrading the fan output.

To shield openings for heating and ventilation against undesirable electromagnetic waves. For electronic enclosures where air flow is required for cooling and ventilation but where EMC compliance and dust filtration must be ensured.

EMC Woven mesh ventilation panel used for heating, air flow for cooling and ventilation in electronic enclosures.

Heavy duty EMP vents for Faraday Cages and EMP bunkers are designed for high performance applications, where high attenuation is required, particularly in the H (magnetic) field.

Solid and rigid drilled ventilation panels for EMP applications

To make your vent panel rainproof with the combination of this plastic rain cap

Low frequency magnetic shielding for sensors, PC's and electronic devices.

Mu-ferro foil and tape has been developed for low-frequency (LF) magnetic field shielding.

Magnetic shielding sheets that are thin and flexible with a high permeability

Scientifically engineered chambers provide a laboratory work space of extremely low and homogenous magnetic field for testing and experimentation.

Material for shielding/screening low-frequency magnetic fields. These fields are present in installations where strong currents are generated or transported, for example transformer rooms, power lines, busbar systems, and high-voltage cables.

System to reduce magnetic fields.

Turnkey solution for shielding cables and cable routes in hospitals, laboratories and other workplaces

Measurement, packing, simulation software for magnetic air transport

Soft EMI/RFI shielding gasket for panels, doors and lids.

For doors and panels, very low closure force to prevent bending of doors, lids and panels.

Economical HF gasket which can be supplied in a wide range of dimensions.

Universal EMC gasket to shield lower frequencies

Very small conductive rubber based EMI / RFI shielding gasket used for PCB’s, smart phones and other applications

Clip-on EMI/RFI shielding gaskets with water seal.

Clip-on EMI shielding gaskets, specifically designed for heavy-duty applications

Very small EMI / RFI shielding gasket used for PCB’s, smart phones and other applications

Very small foam based EMI / RFI shielding gasket used for PCB’s, smart phones and other applications

V-shape EMI/RFI shielding gaskets for applications between lids, hinges/locks, door/doorframe

EMI flange seals for electrical connectors, provided with self-adhesive

Universal EMC gasket to shield lower frequencies

Combined EMI-shielding and water-seal gasket for grooves and door/lid constructions

For EMI shielding of panels and screwed applications like displays, windows, and honeycomb

Structure with foam as its intermediate layer for EMI shielding and absorbing gaskets

Conductive felt is a non-woven polyester fabric with an electrically conductive nickel coating

Gasket with a copper strip on the inside to guide higher currents. Can be used for heated windows.

High conductive metallized fabric HF shielding gasket with high shielding performance.

Creates a positive seal between bottom of door/panel

A gasket for doors and panels with a magnetic strip inside. Very low closure force

High deflection, low closure force gaskets without tooling costs. Any shape or size.

Conductive fabrics with Ni/Cu-layer over P-shaped sponge core (elastomer core)

EMI gaskets with water seal for screwed applications like panels, displays, and windows.

EMI/RFI shielding gasket with low closure force to prevent bending of doors, lids and panels

Gasket die-cut according to the client out of various materials.

Clip-on EMI/RFI shielding gaskets with water seal.

Conductive Rubber O-profiles developed for high performance shielding.

Electrically conductive rubber profiles in general are known for their excellent weather-, oxidation and ozone resistance

Electrically conductive rubber profiles made from silver plated aluminium rubber in general are known for their excellent weather-, oxidation and ozone resistance

Electrically conductive rubber profiles made of carbon filled rubber in general are known for their excellent weather-, oxidation and ozone resistance

The rubber is made conductive by incorporating small conductive carbon particles throughout the material.

In EMI shielding, this rubber in particular is used as a medium to provide electrical conductivity

Very soft conductive rubber, hardness in shore A 20, colour dark red.

Silicone sheet material with oriented wires for EMI shielding and IP sealing.

EMC-IP gasket with controlled compression stops for EMI and EMP protection

Gasket covered with conductive textile and closed-cell neoprene

For thin doors and lids. This L-shaped gasket is used to achieve two goals at once: a water seal and an EMI seal.

All side views of the Fingerstrip gaskets clearly and in a row.

This simple clamping system is suitable for sealing gaps

Snap-on fingerstrip gaskets can be attached on tracks, rails, through holes or slots.

Stick-on mounting fingerstrip gaskets are suitable for gaps from 0 to 3 mm

Pressure sensitive adhesive (PSA) are suitable for low-profile, bi-directional applications and gaps from 3 to 6 mm

Pressure-sensitive adhesive (PSA) are suitable for low-profile, bi-directional applications and gaps  from 6 to 11 mm

These fingerstrips are electronic gaskets for general EMI-shielding applications where there is a narrow opening or gap.

Ideal for 90° applications, where the gasket has to be mounted onto a surface perpendicular to the finger compression area.

Are used for grounding and EMI shielding in high-frequency equipment and for forming large-diameter rings of round contact

Cost-effective long term EMI/RFI performance be/cu fingerstrips with a very dynamic spring range

BeCu EMI Contact fingers for Faraday cage doors and lids for shielded enclosures

A alternative solution of BeCu fingerstrips made out of high conductive material

Grounding / EMI/ RFI contacts Surface mount spring contacts available in different sizes

A small pin which is to be attached by soldering after insertion through the PCB. Used to mount PCB shielding cans

Maximum clamping range, 0,3 mm. Footprint dimensions of the clip 9,40 mm x 2,28 mm.

Clip for mounting PCB shielding cans. This clip offers a fast solution for assembling RFI/EMI shieldings and PCB's. Footprint dimensions of the clip 0,8 mm x 6,5 mm.

Maximum clamping range, 0.12 to 0.23 mm. Footprint dimensions of the clip 1,1 mm x 6 mm

Maximum clamping range, 0,18 to 0,25 mm. Footprint dimensions of the clip 0,8 mm x 4,7 x 4,7 mm.

Clip for mounting PCB shielding cans. This clip offers a fast solution for assembling RFI/EMI shieldings and PCBs. Footprint dimensions of the clip 0,7 mm x 4,5 mm.

Clip for mounting EMI/RFI-shielding cans to PCBs. This SMT (surface mount) clip offers a fast solution for assembling PCB shields. Footprint dimensions of the clip 0,8 mm x 3,8 x 3,8 mm.

Mu-copper housings and enclosures for EMI shielding of PCB’s

High performance double-layer shielded enclosures, produced in any shape or size

We provide customized solutions for EMI shields, grounding contacts, flexible antenna paths, electrically conductive connections, current flows, ESD/EMC stickers to shield plastic housings and more - for a wide variety of applications.

Good elastic recovery and electric properties, for electrical connecting between electrical objects

PCB shielding gaskets are a Surface Mountable Technology (SMT) compatible electric elastomer connector which has good elastic recovery and electric property

Surface Mountable Technology(SMT) compatible electric elastomer connector on PCB level

Grounding / EMI/ RFI contacts Surface mount spring contacts available in different sizes

EMI/RFI shielding and screening cans/covers for printed circuit boards

High quantity PCB shielding is possible from 1.000-250.000+ items

A fence and a removable cover creating a very rigid shielding can for printed circuit boards. The fence needs to be fixed to the PCB with SMD clips

PCB shielding cans with teeth in order to glue the can onto the PCB. No clips are needed for mounting.

Used to create EMI/RFI-shielded compartments on a PCB

EMI RFI Drawn Board level screening and shielding cans and/or covers for PCB’s

Developed to shield only a part of the printed circuit board EMI EMC RFI PCB

This sensor can measure both the position as well as the force used on it.

The Impact locator is used as a landing target which registrates and displays the first landing point on the target pad

For measurement of small movements. Stretch materials up to 30% without permanently deforming

Measurement, packing, simulation software for magnetic air transport

EMI/RFI shielding solutions for electric vehicle (EV) charging stations

Low-frequency and high-frequency field strength measurements on location, EMF Measurements, EM Measurement and HF-field strength measurements

Shielding effectiveness testing for housings enclosures in house and on location. Range of DC to 75 Ghz

Power and signal line filters testing for insertion loss, shielding effectiveness and current leakage. In house PCI (Pulse Current Injection) testing to mill std 188-125 E1 E2. 380 kV 5 kAmp

If you want to make sure that your EMP filters will survive an EMP, then we can perform these test for you.

Engineering test support in any stage of the product; idea, primary design, proto, finished product.

Developing an In-House EMC Troubleshooting and pre-compliance test labs

Our prefabricated self-standing modular Faraday cages offer superior screening of RF/LF/HF signals, e.g. for R&D, TEMPEST, Sensitive Compartmented Information Facility (SCIF) and Testing purposes.

Nonflammable high power handling EM absorbers for anechoic chambers.

Cost effective instant Faraday tent for EMC experiments, RF measurements, mobile military / forensic activities and personal protection.

Shielded doors for use in Faraday cages and EMI/RFI shielded rooms screening of RF/LF/HF signals, e.g. for R&D, TEMPEST, Sensitive Compartmented Information Facility (SCIF) and Testing purposes.

Amucor foil has high attenuation properties in the electrical field (up to 100 dB) as well as in the magnetic field. It is easy to apply, like wallpaper, thanks to its special adhesive for walls, ceilings and floors. The interior finish can be plaster board, foam tiles or plywood.

Mu-Copper foil has high attenuation properties in the electrical field (up to 120 dB) as well as in the magnetic field.

Shielded door specialy for RF shielding and MRI applications

The Anechoic Chambers show superb shielding performance and are mainly applied in EM emission testing according to commercial and military standards

Ready to install Faraday cage windows. These windows guarantee very high EMI / RFI / EMC shielding performance

EMI/RFI shielded mesh foil windows and electrically conductive windows with high EMI/RFI shielding performance. Windows for Electromagnetic Compatibility.

EMI shielded ventilation panels for ventilation and heating in screened rooms, EMI shielding rooms & Faraday cages

A signaljammer car must be shielded to protect the people who drive the car against the massive electromagnetic fields and radio frequencies that are spread and sent by the jammers on top of the car.

Ferrite absorber tile is the industry standard solution and exhibits excellent overall performance versus cost

Power and signal line filters designed for high performance shielded cabinets, shielded rooms and anechoic chambers. Shielding performance: 100dB @ 14KHz-40GHz (MIL-STD-285)

Metal tubes designed to block electromagnetic waves for non metallic materials

Make use of our advanced techniques and revolutionary design ideas necessary to build dependable, state-of-the-art MRI facilities.

EMI shielding metal racks and enclosures, standard size or fully customized

Desktop type shielded box for testing. Measurement working size 515 (W) * 550 (D) * 515 (H)

Compact shielded box to block wireless communication during testing and measurements; working size 200(W)*334(D)*115(H)

Shielded box for testing. Working size 350(W)*400(D)*300(H)

Investigation box with built-in led light and shielded gloves; working size 500(W)*400(D)*406(H)

Big size shielded box for laboratory purposes; working size 698(W)*686(D)*696(H)

Up to 120 dB attenuation over a wide frequency range. Shielded box for wireless testing & forensics with very high performance.

Shielded boxes can be extended with different types of filters. All available types of filters can be found below.

Safe data transport with the shielded briefcase

Test box with automatic open & closure system. Working size 433 x 440 x 313 mm.

Shielded box made from our patented Mu-ferro HD material specially developed for shielding low frequency fields.

Medium shielded experiment box to block wireless communication during testing and measurements working size 224.6 (W) * 320 (D) * 162.3 (H)

Box with amucor lined inside. Easy transport and prototyping

The briefcase blocks wireless communication and sound recording

A large series of electrically conductive tapes for EMI/RFI shielding, ideal for grounding, conductance and EMI/RFI shielding of housings / Faraday cages.

Mu-ferro foil and tape has been developed for low-frequency (LF) magnetic field shielding.

Amucor foil and tape for EMI shielding. Amucor foil or tape can be used to shield plastic housings and enclosures.

Electrically conductive mounting tape for conductivity and EMI shielding

Semiconductive non-woven tape or foil in any width or shape, mainly suitable for ESD applications.

Semiconductive non-woven tape or foil in any width or shape. Mainly suitable for ESD applications.

Aluminium tape especially for EMI/RFI shielding/screening in aluminium housings and frames to prevent galvanic corrosion.

Conductive Foam tape is an Electrically Conductive Open cell Foam elastomer. With high compressibility and superior resilience property: requiring minimal force for high compression and recovering very fast from compression.

Conductive textile is a nylon ribstop, metalized with Cu/Ni, extremely strong and flexible. Very easy to appy to plastic housings to create EMI shielded housing.

A metal tape with a highly conductive self-adhesive on one side and masking tape on the other side.

For high performance contacts in harsh environments

Conductive textile is a nylon ribstop, metalized with Cu/Ni, extremely strong and flexible. Very easy to appy to plastic housings to create EMI shielded housing.

Mu-copper foil and sheets for EMI shielding can be used to shield plastic housings and enclosures or for complete shielding of existing rooms in buildings, to create a Faraday cage.

Amucor foil and tape for EMI shielding. Amucor foil or tape can be used to shield plastic housings and enclosures.

Especially developed for aluminium housings and frames to prevent galvanic corrosion.

Stretch conductive fabric coated with medical-grade silver coating for EMI. Highly conductive, conductivity increases by up to 25% as stretches.

Copper/Nickel conductive non-woven fabric for EMI shielding applications.

shielding performance on a washable conductive fabric for various applications.

Magnetic shielding sheets that are thin and flexible with a high permeability

Amucor foil with reinforcement net for EMI shielding where a strong but also very wide shielding film is required.

All of our EMI shielding gaskets can be provided with these special fabrics.

The rubber is made conductive by incorporating small conductive carbon particles throughout the material. It can provide an EMI-proof and watertight seal in narrow constructions.

Used at higher frequencies than traditional shielding and can also be used with other EMI/RFI shields to extend frequency range.

Transparent static dissipative, self-adhesive Polyester film. It includes a special coating on one side and a release film on the other side.

Semiconductive non-woven tape or foil in any width or shape, mainly suitable for ESD applications.

Aerosol permanently conductive graphene hybrid translucent acrylic paint. Applications in lighting, windows, clear covers and lids, displays etc.

A shielded transparent film in order to apply on standard displays, glass, acrylic, polycarbonate etc.

A polyester film with a layer of transparent conductive coating. This offers excellent electrical and electromagnetic shielding.

Conductive mesh is coated Nickel and Copper over Polyester Fabrics. It offers excellent surface conductivity, shielding effectiveness, and corrosion resistance for a variety of application.

PET film deposited with copper grid and protected with a nickel layer for EMI shielded windows & displays. High light transmission, excellent EMI shielding.

Transparent static dissipative, self-adhesive Polyester film. It includes a special coating on one side and a release film on the other side.

Light weight material conductive mesh offers excellent surface conductivity.

EMI/RFI shielding of plastic enclosures/housings can be done by using an electrically conductive paint containing nickel

EMI/RFI shielding application for prototype and touch up work of plastic enclosures/housings

Aerosol permanently conductive graphene hybrid translucent acrylic paint. Applications in lighting, windows, clear covers and lids, displays etc.

Silver-pigmented conductive coating designed to offer more coverage while maintaining very high conductivity

An electrically conductive silicone grease for improving electrical connections between sliding surfaces and parts

High conductivity for flexible surfaces

A water based epoxy with hardener for floors

Shielded carbon paint for use in and outside

High temperature conductive coating

For higher EMI/RFI shielding demands and larger quantities we can sputter a fully metal, electrically conductive coating onto 90% of all commonly used plastics.

The Glue Needle is ideal for applying small amounts of glue. The content consists of electrically conductive silver glue.

Shieldoseal creates a electrically and thermally conductive connection between components. Used for ESD and EMI shielding applications.

Electrically conductive glue/adhesive. Shieldokit creates an electrically and thermally conductive connection between components.

manual gun for the shieldoseal plastic cardridge

Pneumatic gun for the shieldoseal plastic cardridge

Thermal interface materials (TIMs) are designed to fill in air gaps and microscopic irregularities

Ceramic-filled single-component silicone with high thermal conductivity.

Designed for a well-grounded shielded cabinet with a rated voltage of up to 250 VAC / 50 Hz 250 volt 0 - 60 Hz. Shielding performance: up to 100 dB @ 14 kHz - 40 GHz (MIL-STD-285 or ASTM E 1851)

For anechoic chamber, shielded room, cabinet and shelter, where the effective suppression of radiated and conducted emission is required. Insertion loss: 100 dB @ 14 kHz-40 GHz (MIL-STD-220C).

For shielded rooms where the effective suppression of radiated emission is required. Shielding performance: 100 dB @ 14 kHz-40 GHz (MIL-STD-285)

Used for EMI suppression of all electrical installations and equipment. Shielding performance: 100 dB @ 1 MHz - 40 GHz (MIL-STD-285)

The 8080 HEMP/NEMP powerline series are designed to withstand an unlimited amount of EMP hits and comply with the highest standards and to meet the MIL-STD-188-125 in shielding effectiveness and the E1 and E2 pulse compliance.

Ground filters are capable of reducing unwanted noise while maintaining all safety practices. Frequency range of 14 kHz till 40 GHz, attenuation of 100 dB

Power and signal line filters designed for high performance shielded cabinets, shielded rooms and anechoic chambers. Shielding performance: 100dB @ 14KHz-40GHz (MIL-STD-285)

This series of signal filters are used for telephone, data communication, control, and fire alarm

Shielded boxes can be extended with different types of filters. All available types of filters can be found below.

EMI Shielded room and Faraday cage feedthrough for high speed Ethernet / UTP communication links

The Fiber-optic ethernet converter set with casing can be easilly mounted between the walls of a shielded room and faraday cage and offers a high-speed Ethernet/UTP communication links

Audio, video & USB Data line filter for Faraday cages and EMI screen rooms.

For dual S/PDIF signals (dual coax).

Shielded boxes can be extended with different types of filters. All available types of filters can be found below.

Robust EMP-proof Ethernet converter filter for EMI-shielded rooms and Faraday cages.

The 10 Gbit LAN filter is made to transfer ethernet between 10 Mbps up to 10 Gbps while rejecting interfering frequencies. It rejects external frequencies from 100 MHz to 40 GHz at above 100 dB.

Metal tubes designed to block electromagnetic waves for non metallic materials

Fiber optic waveguides with a average shielding value between 100dB @ up to 18GHz and 80dB @ up to 40GHz.

USB 3.0 converter set converts USB 3.0 signal to an optical signal and passes the signal through a waveguide into the shielded room.

Lightweight, flexible and high performing RF / EMI Shielding Pouche for mobile phone

Lightweight, flexible and high performing RF / EMI Shielding Pouche for mobile phone

Lightweight, flexible and high performing RF / EMI Shielding Pouche for mobile phone

Lightweight, flexible and high performing RF / EMI Shielding Pouche small wallet

Lightweight, flexible and high performing RF / EMI Shielding pouche for tablets

Lightweight, flexible and high performing RF / EMI Shielding Pouche for tablets

Lightweight, flexible and high performing RF / EMI Shielding Pouche medium size

Lightweight, flexible and high performing RF / EMI Shielding Pouche for laptops

Lightweight, flexible and high shielding performing pouches for electronic car keys, RFID devices, credit cards and much more. The shielding pouches can be made in any shape and size.

In EMI shielding, this rubber in particular is used as a medium to provide electrical conductivity

Conductive rubber with small metal particles to provide a EMI proof and watertight seal in narrow constructions

The rubber is made conductive by incorporating small conductive carbon particles throughout the material. It can provide an EMI-proof and watertight seal in narrow constructions.

Nickel filled graphite conductive rubber is used in a general for EMI shielded applications but also for EMP protection. Sheets or die-cut/flash cut accrording to drawing.

Very soft conductive rubber, hardness in shore A 20, colour dark red.

Conductive fluorosilicone elastomer is a 65-durometer, electrically conductive, silver-aluminium shielding fluorosilicone that is designed to meet MIL-DTL-83528 Type D.

Structure with foam as its intermediate layer for EMI shielding and absorbing gaskets

Conductive felt is a non-woven polyester fabric with an electrically conductive nickel coating

Silicone sheet material with oriented wires for EMI shielding and IP sealing.

Electrically conductive rubber profiles made from silver plated aluminium rubber in general are known for their excellent weather-, oxidation and ozone resistance

The rubber is made conductive by incorporating small conductive carbon particles throughout the material.

Electrically conductive rubber profiles made of carbon filled rubber in general are known for their excellent weather-, oxidation and ozone resistance

Electrically conductive rubber profiles in general are known for their excellent weather-, oxidation and ozone resistance

Conductive Rubber O-profiles developed for high performance shielding.

For EMI shielding applications in grooves. Also suitable where IP seal is required

Amucor foil has high attenuation properties in the electrical field (up to 100 dB) as well as in the magnetic field. It is easy to apply, like wallpaper, thanks to its special adhesive for walls, ceilings and floors. The interior finish can be plaster board, foam tiles or plywood.

Mu-Copper foil has high attenuation properties in the electrical field (up to 120 dB) as well as in the magnetic field.

Cost effective instant Faraday tent for EMC experiments, RF measurements, mobile military / forensic activities and personal protection.

The Anechoic Chambers show superb shielding performance and are mainly applied in EM emission testing according to commercial and military standards

Nonflammable high power handling EM absorbers for anechoic chambers.

EMI shielding metal racks and enclosures, standard size or fully customized

Protection for people with EMI/RF sensitivity and people who work in an industry with strong RF fields.

EMI / EMF head and neck protection

Blocks Microwaves by 96%

High silver content which makes the shielding effect very good.

High silver content which makes the shielding effect very good.

The Finger Faraday Cage!

Our light weight shielded hats are a reliable protection for your head against HF-radiation.

Blocks Microwaves by 99.7%

RFID have serious disadvantages such as risks to privacy and undetected fraud. All this can be done while you think you have stored your passport 'safe'. Theoretically, it is even possible to read and / or edit it a chip from 3 to 4 meters away.

Prevents unauthorized access to your RFID card information. For ID, credit and bank cards.

This RFID card badgeholder puts the user in control of where and when their id card is read.

EMI shielding curtains are a high performance mesh or conductive fabric designed to block EMF penetrating into your room.

The shielded sleeping bags are made of conductive textile, which gives a reliable protection against HF radiation, caused by cell phones, DECT-phones, Baby monitors, Wifi, TETRA, etc.

Lightweight, Flexible and High Performance RF / EMI Shielding Pouches to protect and secure your modern car key against wireless signals and digital theft

The shield protects the unborn child from radiation coming from, for example, laptops and mobile phones.